Retrofit kit (compatible with BMW F/G/E chassis). Trim removal tools. Pick tool. T20 Torx screwdriver. Ratchet wrench. Ensure the ignition is turned off. Remove the keys from the vehicle. Open the trunk. Disconnect the negative terminal of the batter

<h2 data-start="232" data-end="256" id="isPasted">Tools Required</h2><ul data-start="258" data-end="391"><li data-start="258" data-end="310">Retrofit kit (compatible with BMW F/G/E chassis)</li><li data-start="311" data-end="333">Trim removal tools</li><li data-start="334" data-end="347">Pick tool</li><li data-start="348" data-end="372">T20 Torx screwdriver</li><li data-start="373" data-end="391">Ratchet wrench</li></ul><hr data-start="393" data-end="396"><h2 data-start="398" data-end="420" id="1&#xFE0F;preparation">1&#xFE0F;.&#xA0;Preparation</h2><ul data-start="422" data-end="588"><li data-start="422" data-end="460">Ensure the ignition is turned off.</li><li data-start="461" data-end="498">Remove the keys from the vehicle.</li><li data-start="499" data-end="518">Open the trunk.</li><li data-start="519" data-end="588">Disconnect the negative terminal of the battery using a wrench.</li></ul><hr data-start="590" data-end="593"><h2 data-start="595" data-end="624" id="2&#xFE0F;remove-trim-panels">2&#xFE0F;.&#xA0;Remove Trim Panels</h2><ul data-start="626" data-end="934"><li data-start="626" data-end="729">Use trim removal tools to gently pry off panels around:<ul data-start="688" data-end="729"><li data-start="688" data-end="703">Stereo unit</li><li data-start="706" data-end="729">Infotainment screen</li></ul></li><li data-start="730" data-end="816">Disconnect the hazard and lock/unlock connectors behind the AC vents trim.</li><li data-start="817" data-end="890">Be gentle to avoid:<ul data-start="843" data-end="890"><li data-start="843" data-end="861">Breaking clips</li><li data-start="864" data-end="890">Damaging trim surfaces</li></ul></li><li data-start="891" data-end="934">Set all removed trim pieces aside safely.</li></ul><hr data-start="936" data-end="939"><h2 data-start="941" data-end="970" id="3&#xFE0F;remove-stereo-unit">3&#xFE0F;.&#xA0;Remove Stereo Unit</h2><ul data-start="972" data-end="1268"><li data-start="972" data-end="1049">Use a T20 Torx screwdriver to remove screws securing the stereo unit.</li><li data-start="1050" data-end="1090">Gently pull the stereo unit forward.</li><li data-start="1091" data-end="1157">Disconnect the main wiring harness (&quot;black squared&quot; plug).</li><li data-start="1158" data-end="1224">Be cautious not to:<ul data-start="1184" data-end="1224"><li data-start="1184" data-end="1201">Pull too hard</li><li data-start="1204" data-end="1224">Damage any wires</li></ul></li><li data-start="1225" data-end="1268">Place the stereo unit in a safe location.</li></ul><hr data-start="1270" data-end="1273"><h2 data-start="1275" data-end="1306" id="4&#xFE0F;install-retrofit-kit">4&#xFE0F;.&#xA0;Install Retrofit Kit</h2><ul data-start="1308" data-end="1922"><li data-start="1308" data-end="1401">Connect the retrofit adapter harness to the stereo using the black squared connector.</li><li data-start="1402" data-end="1462">Plug the OEM connector into the new adapter harness.</li><li data-start="1463" data-end="1650">Important:<ul data-start="1484" data-end="1650"><li data-start="1484" data-end="1555">Transfer the optical cable into the new black squared connector</li><li data-start="1558" data-end="1650">This step is essential for audio functionality (especially for NBT and NBT EVO systems).</li></ul></li><li data-start="1651" data-end="1724">Ensure all harnesses are:<ul data-start="1683" data-end="1724"><li data-start="1683" data-end="1705">Securely connected</li><li data-start="1708" data-end="1724">Fully seated</li></ul></li><li data-start="1725" data-end="1800">Mount additional components (if included in the kit) behind the screen.</li><li data-start="1801" data-end="1922">Optional:<ul data-start="1821" data-end="1922"><li data-start="1821" data-end="1922">Connect the included USB harness for:<ul data-start="1867" data-end="1922"><li data-start="1867" data-end="1879">Dash cam</li><li data-start="1884" data-end="1901">Backup camera</li><li data-start="1906" data-end="1922">Phone charging</li></ul></li></ul></li></ul><hr data-start="1924" data-end="1927"><h2 data-start="1929" data-end="1970" id="5&#xFE0F;connect-to-infotainment-system">5&#xFE0F;.&#xA0;Connect to Infotainment System</h2><ul data-start="1972" data-end="2272"><li data-start="1972" data-end="2105">Plug retrofit harnesses into the appropriate ports on the back of the infotainment screen:<ul data-start="2069" data-end="2105"><li data-start="2069" data-end="2105">Typically small white connectors</li></ul></li><li data-start="2106" data-end="2198">Connect all auxiliary wires:<ul data-start="2141" data-end="2198"><li data-start="2141" data-end="2156">GPS antenna</li><li data-start="2159" data-end="2179">Microphone (MIC)</li><li data-start="2182" data-end="2198">WiFi antenna</li></ul></li><li data-start="2199" data-end="2272">Double-check that all connectors are firmly seated to avoid issues.</li></ul><hr data-start="2274" data-end="2277"><h2 data-start="2279" data-end="2320" id="6&#xFE0F;reinstall-stereo-unit-and-trim">6&#xFE0F;.&#xA0;Reinstall Stereo Unit and Trim</h2><ul data-start="2322" data-end="2535"><li data-start="2322" data-end="2375">Tuck excess wiring neatly behind the stereo unit.</li><li data-start="2376" data-end="2450">Use the T20 Torx screwdriver to secure the stereo back into place.</li><li data-start="2451" data-end="2535">Reinstall all trim panels around the screen and controls by snapping them back in.</li></ul><hr data-start="2537" data-end="2540"><h2 data-start="2542" data-end="2570" id="7&#xFE0F;reconnect-battery">7&#xFE0F;.&#xA0;Reconnect Battery</h2><ul data-start="2572" data-end="2668"><li data-start="2572" data-end="2620">Reconnect the negative battery terminal.</li><li data-start="2621" data-end="2668">Tighten the terminal securely using a wrench.</li></ul><hr data-start="2670" data-end="2673"><h2 data-start="2675" data-end="2710" id="8&#xFE0F;testing-and-final-checks">8&#xFE0F;.&#xA0;Testing and Final Checks</h2><ul data-start="2712" data-end="2995"><li data-start="2712" data-end="2770">Start the vehicle to power on the infotainment system.</li><li data-start="2771" data-end="2835">Connect your smartphone via:<ul data-start="2806" data-end="2835"><li data-start="2806" data-end="2819">Bluetooth</li><li data-start="2822" data-end="2835">USB cable</li></ul></li><li data-start="2836" data-end="2995">Test functionality of:<ul data-start="2865" data-end="2995"><li data-start="2865" data-end="2882">Apple CarPlay</li><li data-start="2885" data-end="2901">Android Auto</li><li data-start="2904" data-end="2920">Audio system</li><li data-start="2923" data-end="2930">GPS</li><li data-start="2933" data-end="2995">Any auxiliary components (e.g., backup camera, USB charging)</li></ul></li></ul><hr data-start="2997" data-end="3000">&#x2705; Installation Complete! You&apos;re now ready to enjoy your upgraded BMW infotainment experience.

BMW CarPlay Retrofit Installation Guide

Applicable for DRL Module Replacement & RGB LED Integration. T15 Torx screwdriver. Ratchet wrench. Trim removal tool. 10mm socket or wrench. Heat gun. Microfiber towel. Disconnect the Vehicle Battery. Use a 10mm socket or wrench to disconnect the neg

Applicable for DRL Module Replacement &amp; RGB LED Integration<hr data-start="249" data-end="252"><h2 data-start="254" data-end="275" id="tools-required">Tools Required</h2><ul data-start="277" data-end="402"><li data-start="277" data-end="301">T15 Torx screwdriver</li><li data-start="302" data-end="320">Ratchet wrench</li><li data-start="321" data-end="342">Trim removal tool</li><li data-start="343" data-end="368">10mm socket or wrench</li><li data-start="369" data-end="381">Heat gun</li><li data-start="382" data-end="402">Microfiber towel</li></ul><hr data-start="404" data-end="407"><h2 data-start="409" data-end="435" id="step-1-preparation">Step 1: Preparation</h2><ol data-start="437" data-end="861"><li data-start="437" data-end="617">Disconnect the Vehicle Battery<ul data-start="480" data-end="617"><li data-start="480" data-end="617">Use a 10mm socket or wrench to disconnect the negative terminal of your battery to avoid electrical shorts during installation.</li></ul></li><li data-start="619" data-end="861">Locate the DRL Modules<ul data-start="654" data-end="861"><li data-start="654" data-end="734">Find the Daytime Running Light (DRL) modules on your headlight housings.</li><li data-start="738" data-end="861">Their location may vary depending on your vehicle model&#x2014;typically on the top, back, or bottom of the headlight units.</li></ul></li></ol><hr data-start="863" data-end="866"><h2 data-start="868" data-end="912" id="step-2-remove-drl-modules-and-boards">Step 2: Remove DRL Modules and Boards</h2><ol data-start="914" data-end="1141"><li data-start="914" data-end="1022">Use a T15 Torx screwdriver to remove the screws securing the DRL modules to the headlight housings.</li><li data-start="1023" data-end="1089">Disconnect the wiring connectors from the DRL LED boards.</li><li data-start="1090" data-end="1141">Carefully set the modules aside in a safe place.</li></ol><hr data-start="1143" data-end="1146"><h2 data-start="1148" data-end="1202" id="step-3-separate-the-led-boards-from-the-module">Step 3: Separate the LED Boards from the Module</h2><ol data-start="1204" data-end="1529"><li data-start="1204" data-end="1354">Use a heat gun to warm up the rear of the DRL module where factory adhesive is applied.<ul data-start="1304" data-end="1354"><li data-start="1304" data-end="1354">This softens the paste and makes removal easier.</li></ul></li><li data-start="1356" data-end="1529">Using a trim tool, gently pry up the edges of the LED board to separate it from the module housing.<ul data-start="1472" data-end="1529"><li data-start="1472" data-end="1529">Be careful not to crack the board or damage the module.</li></ul></li></ol><hr data-start="1531" data-end="1534"><h2 data-start="1536" data-end="1577" id="step-4-install-new-drl-led-boards">Step 4: Install New DRL LED Boards</h2><ol data-start="1579" data-end="1981"><li data-start="1579" data-end="1701">Clean the Module Housing<ul data-start="1616" data-end="1701"><li data-start="1616" data-end="1701">Scrape off any old adhesive residue and wipe clean with a microfiber towel.</li></ul></li><li data-start="1703" data-end="1912">Apply Thermal Adhesive or Heat Sink Glue<ul data-start="1756" data-end="1912"><li data-start="1756" data-end="1838">Spread an even layer of thermal glue on the back of the new DRL LED board.</li><li data-start="1842" data-end="1912">Do not over-apply to avoid glue leaking onto circuit components.</li></ul></li><li data-start="1914" data-end="1981">Let the glue cure for at least 15 minutes before continuing.</li></ol><hr data-start="1983" data-end="1986"><h2 data-start="1988" data-end="2024" id="step-5-reinstall-drl-modules">Step 5: Reinstall DRL Modules</h2><ol data-start="2026" data-end="2381"><li data-start="2026" data-end="2227">Once the adhesive is cured and the boards are firmly in place:<ul data-start="2097" data-end="2227"><li data-start="2097" data-end="2140">Reconnect the LED board connectors.</li><li data-start="2144" data-end="2227">Secure the modules back onto the headlight housing using the T15 Torx screws.</li></ul></li><li data-start="2229" data-end="2381">Reconnect the vehicle battery and switch the DRL setting to ON to test:<ul data-start="2317" data-end="2381"><li data-start="2317" data-end="2342">DRL lighting function</li><li data-start="2346" data-end="2381">Blinker/indicator functionality</li></ul></li></ol><hr data-start="2383" data-end="2386"><h2 data-start="2388" data-end="2438" id="for-rgb-drl-users-continue-to-steps-67">For RGB DRL Users: Continue to Steps 6&#x2013;7</h2><hr data-start="2440" data-end="2443"><h2 data-start="2445" data-end="2486" id="step-6-install-rgb-wiring-harness">Step 6: Install RGB Wiring Harness</h2><ol data-start="2488" data-end="3101"><li data-start="2488" data-end="2569">On the driver&#x2019;s side headlight, unplug the main headlight connector.</li><li data-start="2570" data-end="2755">Connect the included RGB harness adapter:<ul data-start="2624" data-end="2755"><li data-start="2624" data-end="2671">One end goes to the original headlight plug</li><li data-start="2675" data-end="2755">The other end connects to the RGB DRL LED control module (small black box)</li></ul></li><li data-start="2757" data-end="2958">Use the interconnect harness (with two small white connectors) to bridge both headlight modules.<ul data-start="2870" data-end="2958"><li data-start="2870" data-end="2958">Plug each end into the corresponding control boxes on both driver and passenger sides.</li></ul></li><li data-start="2960" data-end="3101">Once connections are complete, reconnect the vehicle battery and turn the DRL switch ON inside your vehicle to test RGB functions.</li></ol><hr data-start="3103" data-end="3106"><h2 data-start="3108" data-end="3156" id="step-7-configure-rgb-with-magicstrip-app">Step 7: Configure RGB with MAGICSTRIP App</h2><ol data-start="3158" data-end="3523"><li data-start="3158" data-end="3243">Download the MAGICSTRIP app (purple icon) from the App Store or Google Play.</li><li data-start="3244" data-end="3315">Open the app and tap the menu icon (&#x2630;) in the top-left corner.</li><li data-start="3316" data-end="3402">Your RGB DRLs should appear in the device list. Tap to connect via Bluetooth.</li><li data-start="3403" data-end="3523">You can now control:<ul data-start="3432" data-end="3523"><li data-start="3432" data-end="3455">Color selection</li><li data-start="3459" data-end="3481">Lighting modes</li><li data-start="3485" data-end="3523">Brightness and speed adjustments</li></ul></li></ol><hr data-start="3525" data-end="3528"><h2 data-start="3530" data-end="3561" id="installation-complete">Installation Complete!</h2>Enjoy your upgraded DRLs with full RGB customization. Make sure to test all light modes and confirm secure installation before driving.

DRL LED Module & RGB Upgrade Installation Guide

Home

Shop

Bimmer Plug

Discover the Bimmer Plug Master Installation Guide, your ultimate resource for step-by-step instructions on installing our premium carbon fiber parts and automotive upgrades.

Master Installation Guide | Bimmer Plug - Step-by-Step Instructions for Premium Parts

INSTALLATION GUIDE

Is Bimmer Plug Good And Reliable?

Where Is Bimmer Plug Located?

Do I Need Professional Installation or Can I install It Myself?

What Is Your Return Policy?

How Do I Find More Products For My Car?

Are There Any Discounts Or Promotions?

Does Bimmer Plug have a Trusted Testimony?

How Do I Create My Account?

GENERAL INFORMATION

What Is Carbon Fiber And Why Carbon Fiber?

Where Are Bimmer Plug Products Made?

Are These Genuine Carbon Fiber or Carbon Fiber Overlay Parts?

Are Your Parts Tested For Quality and Durability?

Will These Parts Fit My Specific BMW Model & Year?

What If the Product Doesn’t Fit or I Change My Mind?

PRODUCT KNOWLEDGE & INFORMATION

What Do I Do If My Package Is Lost?

Can I Cancel Or Change My Shipping Address After Placing My Order?

How Can I Track My Order?

How Long Does Shipping Take and Where Do You Ship From?

ORDERS & SHIPPING INFORMATION

What Payment Methods Do You Accept?

Is It Safe To Enter My Credit Card Information On Your Website?

Will I Receive An Invoice For My Purchase?

What Should I Do If I Encounter Payment-Related Issues During Checkout?

Can I Finance Or Pay In Installments?

PAYMENT METHODS

What Warranty Do You Offer On Your Products?

Are There Any Shipping Restrictions Or Additional Customs Fees?

Do You Offer International Shipping?

RETURNS, EXCHANGES & WARRANTY

What is our Affiliate Program?

How Does the Affiliate Program Work, and How Can I Get Started?

What Are The Benefits Of Joining The Affiliate Program?

What kind of promotional materials and tools will I receive as an affiliate?

What Is The Commission Structure, How, and When Will I Get Paid?

Can I promote affiliate links on social media, and how should I do it effectively?

Are there any geographical restrictions to becoming an affiliate?

How Can I Get Help Or Support If I Encounter Any Issues With The Affiliate Program?

AFFILIATES

What’s The Best Way To Contact The Bimmer Plug Team?

CONTACT INFROMATION & BUSINESS HOUR